This is part 2 of our rubber roofing guide. In this part we will explain shortcomings of rubber roof (such as inherently faulty design), inability to hold ponding water and generally short life span, etc.

We will aslo demonstrate how many roofers are “trained” in installation of EPDM single ply roofing systems, results of their work (our Horrible Rubber Roofs series), and explain why we recommend that you avoid installing a rubber roof on your house.

Read this and you will save yourself lots of cash and many headaches. Also see our special “Horrible Rubber Roofs” video series below!

The truth about residential flat roofing market and contractors.

This rubber roof is just 1 year old, and has been leaking since day one, until we replaced it with a lifetime IB PVC flat roofing membrane.

Rubber Roof Contractors: It is unfortunate, but most residential flat roofs are installed by roofing contractors that specialize in asphalt shingles. Since they can easily purchase rubber roofing materials from their roofing supply warehouse, and are not required to be certified installers, nor do they need any special training or equipment, they will often undertake such projects to keep their crews busy.

Incorrectly installed EPDM roof in Quincy, MA – rubber glued right over shingles:

Horrible Rubber Roofs videos:

Horrible rubber roof part 1.
Location: Brockton, MA
Date taken: SUMMER 2011

Horrible rubber roof part 2.
Location: Revere, MA
Date taken: Fall 2011

Horrible rubber roof part 3.
Location: Country Club in Central MA
Date taken: Summer / Fall 2011

These are just some roof inspections that we did in the summer / fall of 2011. Look – even commercial roofs are not immune to hack roofers and faulty materials (like rubber roofing), but in residential, this is much more common.

Getting a quality flat roof installed:

The truth is that to get a quality rubber roof installed, it usually has to be done by a commercial roofing company that specializes in flat roofing. However, it is often the policy of such companies not to work with residential customers, for which there are many reasons. These contractors work with large commercial and institutional customers, employ union workers who are trained roof mechanics, specializing in their particular niche. For example, a commercial roofing contractor will have separate crews doing metal roofing or slate – these guys are “roofers”, and yet another crew doing flat roofing ONLY – these are “roof mechanics”.

A residential roofing contractor usually employs just roofers, who are good at what they do all day long – install asphalt shingle roofs, and often do not have a clue about how flat roofs work. When they get a potential client with a flat roof, they go to their supplier, ask what supplier has for flat roof, and the salesman at the supply warehouse TEACHES the roofer how to install EPDM rubber. This is not creative fiction or a product of my imagination – I see this happening nearly every time, when I come in to the supply store to get something.

“Trained rubber roofing installers”: If you are lucky, you may get a roofer that has received some sort of training about rubber roof installation. For example, one of my suppliers, provides installation training programs for their roofing contractors who install only asphalt shingles. The idea behind such training seminars is to increase awareness and solicit sales of more roofing products. A manufacturer technician provides a sample installation on a 8×8 feet demo stand.

Bellow is and example of such “hands-on rubber roofing training”.

As you can see, the roofers just sit around the demo stand while the MFG Installation technician shows them what to do. The whole demonstration took about an hour and a half, and covered thing like installing flat roofing insulation (ISO), adhering rubber to the ISO board, flashing a sky-light / chimney penetration with un-cured flashing material, installing the membrane up the vertical wall, cleaning & priming seams and installing seam tape, installing drip edge and a tape to seal the drip edge fasteners, and installing termination bar. In the same 1.5 hours we’ve also “learned” how to correctly apply yellow glue – membrane adhesive, seam primer – seam & flashing glue and how to install these systems in the winter, while violating manufacturer’s installation specs.

Out of 25 or so roofing contractors present, there were about 15 or so questions particular to the installation details. 7 of them where asked by me! Bear in mind that I already knew how to install a rubber roof and attended the event to talk to my salesman, representatives of the metal roofing manufacturer and for free refreshments

In any case, each one of those 25 or so roofing contractors, willing to learn a new, and very complicated roofing system, asked an average of 0.3 questions about this system.

Rubber roofs for residential customers: It was clear that my supplier and the roofing representatives were selling to Residential Roofing Contractors. Not once did they mention roof-top HVAC units, roof hatches, elevator shafts, gas/electrical pipes, roof drains, etc. They did however insist that the rubber is a good choice for a low slope shed dormer (without mentioning the poor low slope roof ventilation and ice dam prevention associated with shed dormers). They also mentioned that rubber is a good choice for a flat roof decks and patios.

We are an Eco-Friendly, full service flat roofing company specializing in installation of Cool Roofing systems for a wide range of Residential and Commercial roofing projects. We carry all necessary General Liability and Worker’s Compensation Insurances, OSHA certifications, and are a Licensed IB Roof installer.

Roof installation service:

We offer a complete-package roof installation service, from pulling all necessary building permits, to coordinating with other contractors and service providers (such as utility companies, architects, etc.) involved in your roofing project.

Our installers and roof mechanics work safely, wear all necessary safety equipment and use state of the art installation tools and equipment. We pay top wages, and provide premium workmanship and services.

While a standard labor warranty in the roofing industry (a minimum required by law) is the 2-year period, all our roof installations include a Labor warranty that matches the material warranty (i.e., 80-mil IB membrane has a 25 year material warranty, which we match with our 25-year labor warranty).

Roof consulting service:

We offer roofing consultation services which include complete analysis of your present roof condition, inspection of structural components, roof deck and roof insulation. We analyze your roof’s drainage situation, and identify whether you may need more insulation, drains / scupper, or other roof components installed to improve your roof’s performance and extend its service life. We will provide you with a complete report of what has to be done on your roof, and identify parts you may not need. We can also negotiate with your General Contractor and/or Architect on your behalf, to get you the right products/services, while including needed items, and eliminating unnecessary and costly items. This will prevent future “change orders” and up-charges from your GC / Architect / Contractor, and save you money and frustration.

We hold all necessary State Construction Licenses and Registrations:

• MA Home-Improvement Contractor registration (HIC) and Unrestricted Construction Supervisor License (CSL)
• CT Home-Improvement Contractor registration (HIC) and Major Contractor Registration
• RI Home-Improvement Registration and Special Commercial Roofing Contractor Registration

Flat Roof installation service details:

For a flat and low-slope roofing application, we exclusively install IB Cool roofing single-ply membranes with up-to 25 years Commercial and Lifetime Residential warranties.

IB Roof is a versatile flat roofing system that can be adapted for any flat roof type and level complexity. IB roof is a perfect, long-lasting flat roofing choice for:

• Condos, Cooperatives and other Multi-Unit residential buildings.
• Restaurants
• Storage Facilities
• Office buildings
• Manufacturing and Warehouse facilities
• Auto Repair stations and garages, Gas Stations
• Stores and Shopping malls
• All other commercial buildings with a flat roof

With its Cool-roof properties, IB will save you an average of 20% or more on the Air-Conditioning costs, which can run into hundreds of dollars per month. With the ever-rising electricity prices, this is especially crucial for climate-controlled storage-complexes, restaurants, and refrigeration-facilities, but will greatly benefit any building that uses Air-Conditioning equipment.

IB is also an environmentally friendly roof and you can have a Green / Garden roof installed, without worries of roof leaks or environmental incompatibility.

IB with its Lifetime Residential warranty, is perfect for any type of residential application: Your Home roof, Garage or even a walk-on flat roof deck. IB can be installed as a water-proofing membrane under a solid wood deck or you can choose an IB DeckShield* – a slip and water-proof, ADA (American Disability Act) compliant decking material. (* Due to anticipated constant foot traffic, IB DeckShield carries a 10 year warranty)

Your One Stop informational source about all aspects Flat Roofing, Cool Roofs, Solar BI-PV Roofs & Roof-top Gardens.

We specialize in Energy-Efficient flat roofing solutions for Residential flat roofs and Commercial / Restaurant flat roofs. We strive to provide our customers, with Eco-Friendly roofing solutions that are recyclable, & will help you conserve energy, as well as benefit environment.

Our Customer’s comments:

CoolFlatRoof installed an IB roof on a flat section of my house. They did an excellent job. I had problems for years with leaks and would hire someone to repair it but after awhile it would leak again. It had never leaked since Leo and Alex put this excellent roof on my house. It also seems to be more insulated: warmer in the winter and cooler in the summer. Thanks guys. I recommend you to everyone who mentions a roofing problem. – Jack from Providence, RI

CoolFlatRoof quality promise: We are so confident in the quality of IB roofing systems and our installation, that we guarantee our roofs against any leaks. If the roof we installed ever leaks due to installation error, not only will we fix it, but we will also give you a check for $250.

Flat Roof leaks and repair information

For your convenience, we created a series of roofing guides that will help you choose the best solution for your flat roof and provide you with information that many roofing contractors and manufacturers do not want you to know. Check out our Do-it-yourself guides to rubber roof repair and tar & gravel roof repair for immediate steps you can take to temporarily stop roof leaks, until you can perform a complete re-roof.

When your flat roof begins to leak, the process is irreversible, and the sooner you start to deal with these issues, the less you will have to spend on repairs and roof replacement. Read our comprehensive Flat Roof repair guide to gain the insight on the issues and costs involved and ways to minimize your expenses when you deal with roof leaks.

Discover different types of flat roofing materials and choose the best roofing product for your home or business. It is a shame that in the 21st century many roofing contractors still use 19th century roofing technology, whih is inferior, inefficient and cost you more than a modern single-ply roof. Learn about different single-ply flat roofing systems and compare them to IB Roofs, the leading manufacturer of long-lasting cool flat roofing products.

Compare the two leading single-ply cool roofing products in our PVC vs. TPO roofing guide.

Flat roofing job profiles: Industrial, Commercial and Residential.

Testex textiles Corp. Central Falls, RI

Restaurant/Meat Market/Deli Rt. 1 – Hampton, NH

9th St. Condominiums Providence, RI

Rubber roofing (EPDM single ply membranes) it the most common flat roofing system in New England (MA, CT, NH, RI, etc.) and the rest of US flat roofing marker – most people refer to a flat roof as “rubber roof”. The main reason for such popularity of rubber roofs is the lower initial roof price. However, rubber roofs have many inherent problems, which cannot be solved by technology, because of the rubber roof’s design, as well as issues with unprofessional roofing contractors claiming to be “rubber roofing pros“.

What you need to know about Rubber Roofing:

There is much confusion about rubber roofing, as well as misunderstanding of its benefits and limitations. In this article we will try to clear up the confusion and show you that rubber roofing is NOT the best flat roofing material, and there are better and cheaper alternatives to rubber.

If you have a leaking rubber roof in Massachusetts, Connecticut or Rhode Island we can give you a roofing price quote to replace your rubber roof with our flat roofing material of choice – a new, lifetime PVC Flat roof manufactured by IB Roof Systems. We can also repair your rubber roof at a relatively low cost, using only the best materials that rubber systems have, and extend the life of your rubber roof by a few years. One example of such materials are peel-and-stick flashing and seam tapes. We do not use black rubber glue as it is outdated, and leaks much faster.

Quick Navigation:

• Why homeowners should avoid rubber roofing – The truth about the residential flat roofing market, why you should stay away from rubber, and carefully choose your roofing contractor.
• Alternatives to rubber roofing – Find out what other, better flat roofing products are available for a similar cost, but without the EPDM’s inherited problems.
• Residential rubber roofing – Learn why rubber roofs should NOT be used on a roof of your home.
• Commercial rubber roofing – Limitations of EPDM rubber in the commercial flat roofing applications.
• Why rubber roofs are so popular – Quick history of EPDM rubber in US flat roofing market, and the key to its popularity

BAD Rubber Roofing Video – this why you don’t want to have a flat rubber roof:

EPDM Rubber roofing and flat roof homes.

Homeowners with flat roof homes often find themselves in a situation where their roof starts to leak rather unexpectedly – i.e. only after a few years since the roof was installed. This for the most part happens to homes that have a rubber roof on them. While most flat roofs will only last 10-15 years, older systems such as Tar & Gravel, Bur and in some cases Modified bitumen roofs are usually installed by roofing contractors that are somewhat specialized in their scope of work – these are “the old-timers” or former union guys that decided to try their luck working for themselves, and they actually went through special training and have years of experience. The problem is that roofing systems they install do not last long for many reasons outside the scope of this article.

Homes that have a rubber roof begin to leak well before their minimal life expectancy is reached because in many cases they are roofed by your typical shingle roofing contractor that is so confident in his/her abilities, and a rubber roof is merely a roof with a low slope.

Why rubber roofs are so popular?

The truth is, rubber roofs (EPDM) are the most used flat roofing products in the US / Canadian commercial roofing market. Rubber roofs we first put in service over 40 years ago, and since gained popularity among roofing contractors and their customers. The reason for such success lyes in the condition of the flat roofing market at that time and the available alternatives.

Back in 1960′s oil was still very cheap, it was more than a decade before the oil crisis of the 70′s and there wasn’t that much demand for oil. The oil refining process was far from being efficient and the industry was looking to get rid of many by-products of the oil refining process.

At the same time, the flat roofing industry was the same as at the turn of the 19th century, and the most common product to use on a flat roof was either a BUR (built-up roofing, using multiple layers of tar paper, saturated in hot tar or hot asphalt) or Tar & Gravel roofing, which was essentially a BUR roof with gravel added for additional protection. Flat roofing technology has not changed for 100 years and contractors needed a new, easier to install and cleaner product, hence, the EPDM was born.

EPDM consists mainly of oil (carbo-hydrate) based by-products with some modifiers and stabilizers added to extend its service life. Rubber roofing was cheap to produce, easier to install than conventional (BUR) roofs, did not require any special equipment to put it down and the membrane could potentially last for decades, as it was UV stable and did not break down when exposed to the weather.

Because rubber roofing was cheap, quick to install, and offered a potentially long service life, and with lack of any opposition from better roofing products, it quickly became the king of flat roofing and the pioneer of the single-ply flat roofing market.

Useful resources:

DIY epdm rubber roof repair – Our original article on how to fix a rubber roof with EPDM rubber adhesive (no peel-n-stick tapes)

Rubber roof repair guide – A part 2 of our Do-it-yourself guide teaching you how to fix EPDM rubber roofing systems with primer and seam tape.

Read part 2 – Why homeowners should avoid Rubber Roof for their homes, see examples of HORRIBLE RUBBER ROOFS, and learn how roofers are “trained in EPDM roof installation” (which is a complete joke)!

In our overview of Flat Roofing Technologies: Part I – BUR, Tar & Gravel and Modified Bitumen, we discussed the older and in many ways inefficient types of flat roofs, that are not only outdated by today’s standards, but also have a short life cycle expectancy. Moreover, they pose numerous obstacles when it comes to repairing those flat roofs, as discussed in our Flat Roof Repair guide. See our comparison of two seemingly similar, yet very different in their nature flat roofing types – PVC and TPO roofs below.

In Part II we will take a look at the newer, more advanced roofing technologies, and explore the advantages and disadvantages of each single-ply roofing technology commonly used today.

What is single-ply flat roofing?

There is a lot of confusion about single ply membrane roofing. Many people think that any ‘single ply’ is the answer to their flat roofing problems. This however is far from being the truth. In reality, single-ply roofing membranes have only one thing in common – that is they are single ply or just one layer of membrane that is a water proofing barrier. The similarity stops there.

Single ply membrane formulation, or the components a membrane is made of, is what makes the difference between different types of single-ply flat roofing membranes. Single ply roofing membranes come in various widths, ranging from 6 to over 18 feet. In theory, the wider the membrane is, the less overlapping seam you have, thus reducing the possibility of leaks. The reality is different however, and most commonly used membranes do not exceed 10 feet in width.

The most crucial aspect to the reliability and longevity of single ply roofs is the method of attaching overlapping seams together. That is where 99% of flat roof leaks occur. Therefore, having permanently attached seams is the most important factor in the longevity of a flat roof installation. We will discuss it in more detail as we review different single ply roofing technologies.

IB Flat Roof installation in Weston, MA

Single-ply membrane installation methods:

Single ply membranes are installed either as fully adhered or mechanically attached systems depending on each roof’s condition, and other factors, as well as an installer’s preferences in some cases. Underneath the membrane there s usually a separation barrier and/or some sort of insulation board. Most common insulation is ISO or EPS foam board. Both types have an R-value ranging from 4-R to 6-R per 1 inch of insulation thickness.

Mechanically attached installation uses heavy duty screws and barbed plates to hold the membrane down tightly, and is not affected by possible ISO de-lamination. The membrane is attached using 12″ O.C. pattern with perimeter sheets attached 6″ O.C. This ensures that even the hurricane-type wind will not tear off your roof. Mechanically attached installation method does not require the use of heavy and expensive ballast, and is a preferred choice if your building is located in the high-wind area, such as along the coast line or on a high hill.

Fully adhered single ply membranes are glued to the fiberglass sheet laminated to both sides of the ISO insulation, which is in turn attached to the roof deck. While quick and simple, the fully adhered method has one serious disadvantage. If condensation forms underneath a roofing membrane, which often happens and may be caused by improper ventilation of the roof deck, it will ‘de-laminate’ the ISO board and/or adhesive that is holding membrane in place. If the membrane becomes loose, it is prone to wind blow-off, which will leave your roof unprotected. Results of such blow-off will be catastrophic not only to your roof, but to the entire building. While this is rarely the case, it is still a possibility – a gamble you might not want to take.

More common problems with fully-adhered single-ply flat roofing systems (Mostly EPDM rubber) are defects in glue/adhesive application that cause bubbles, badly glued seams and as a result, a very unpleasant view and more often then not, roof leaks. The image bellow demonstrates a defective Epdm rubber application.

Find out more information on why you should avoid installing EPDM rubber roofing on you home and how residential roofing contractors are trained to install rubber roofs.

Three most common single-ply roofing types:

Today, single ply roofing has become the prime choice when it comes to flat roof replacement. More and more roofing contractors are switching from old roofing types like BUR, Asphalt, and Tar & Gravel roofs to single-ply membrane installation, which is easier, safer and faster. Single ply roofing installation does not use the torching used in Modified Bitumen roofs installation, and therefore there is no fire hazard/possibility to bur down your home / business.

There are 3 most-used single ply membrane types present on the market today: PVC/CPA, EPDM rubber and TPO. While these abbreviations probably won’t tell you much, about these roof types, bellow we provide a brief summary of each of these technologies.

PVC (CPA) Roofing:

• PVC – Polyvinyl Chloride – a thermoplastic membrane utilizing a reinforcement scrim between the two plies of equal thickness (IB roof only). Top ply contains Cool Roof pigments, UV stabilizers, and other components to extend the life of the membrane. Bottom ply contains PVC ingredients to provide consistent weld of top and bottom plies and fillers. Material Warranty Period: Up to 25 years Commercial / Lifetime Residential. PVC roof system life expectancy: 30+ years.
• Special Notes: For a complete overview of IB flat roofing products for residential, commercial and restaurant use, as well as installation method and roofing accessories refer to our IB Roof products page.

TPO Roofing

• TPO – Thermo Plastic Olefin – a thermoplastic membrane utilizing a reinforcement scrim between the two plies. 35/65 % thickness for top & bottom ply respectively. Top ply contains Cool Roof pigments, UV stabilizers, and other components to extend the life of the membrane. Bottom ply contains TPO ingredients to provide consistent weld of top and bottom plies and fillers. Note that the top ply is about half the thickness of the bottom ply. Yet the top ply is the one that makes the roof long-lasting. IB PVC has a 50/50 or equal thickness of top/bottom ply.
• Material Warranty Period: Up to 20 years Commercial / NO Residential. TPO roof system life expectancy – 7 to 20* years. You should know that there is not a single TPO installation in existence in the USA, that was produced in North America and is older than about 15 years. Therefore it is unknown how long a TPO system will perform without any leaks*.
• Special Notes: * TPO roof systems are under continuous development by numerous manufacturers, who constantly change the TPO formulation to achieve the lowest cost with acceptable performance. While it is understandable that businesses always look to save money and to reduce costs, these constant TPO development process is being conducted, often at the expense of the roof owner. A TPO roof from the same manufacturer will most likely NOT be the same as the one produced few years before or after. Also the quality of different batches of TPO membranes may be questionable, as some TPO producers release the product to the end user without getting the UL and similar approvals/certification, as the formulation changes too often. Refer to our comparison article of PVC vs. TPO to find out more about the TPO problems / short-comings.

EPDM Rubber

• EPDM Rubber – Ethylene Propylene Diene Monomer – a rubber-like black membrane, usually non-reinforced. Most common application method is a fully adhered (glued down) membrane with glued seams / flashings.
• Material Warranty Period: Up to 40 years Commercial / NO Residential. EPDM roof system life expectancy – 10 to 15 years. Although the material warranty goes up to 40 years for a 90-mil Epdm from some manufacturers, it does not cover the seams. Failing seams are the main cause of EPDM roof leaks followed by ponding water, for which EPDM has no warranty either.
• Special Notes: EPDM is the least expensive single ply roofing type and requires no special equipment to install it (unlike PVC and TPO which require hot-air welding equipment) and thus is the first choice for roofing contractors entering the flat roofing market and asphalt shingle roofers, who ‘install rubber here and there’. Although many commercial roofing companies also use EPDM, they usually do not perform Residential installations so many times a home owner deals with a Part-Time flat roofing company.

Badly installed Rubber Roof:

Please note that there are many manufacturers of all three types of roofing, and each has their own formulation / manufacturing process / warranty conditions and periods, etc. Therefore we only provide a general summary for each of those roof types. Also, since our specialty is installation of IB roofs, when we use the term PVC or CPA we refer to IB PVC Roof (CPA or Co-Polymer Alloy is the way IB Roof Systems refers to its PVC product. IB membranes are 100% ‘compatible’ with other PVC products).

Common single-ply flat roofing choices: CPA/PVC membrane – IB Roof

CPA/PVC single play flat roofing membrane made by IB Roof Systems is by far, the best choice for any type of flat roof. The main advantage of IB’s CPA/PVC membrane is that the seams are Hot Air welded creating a physical bond between the sheets, which is stronger than the membrane itself. Such seam is a permanent seal, ensuring that there will be no leaks even if you have puddles of ponding water on your roof (which by the way is covered under IB’s warranty, unlike other types of flat roofing membranes that only cover the defects in material). IB’s CPA/PVC white membrane is the true energy efficient Cool Roof, this will not only give you years of worry-free performance, but will actually save you money in reduced energy costs. IB also offers a variety of colors, many of which will also qualify to carry a Cool Roof label. But the main factor speaking in favor of IB’s CPA/PVC membranes, is that they have historically proven to last over 25 years without a single leak!

Learn more about IB’s outstanding single ply flat roofing membrane, its advantages, and many choices for Residential, Commercial and Restaurant use.

Flat Roofing systems: The purpose of a flat roof or any roof for that matter is to keep your home or building safe and dry. The roof MUST protect your investment from the elements such as rain, snow, and even the sun’s heat. However, many flat roofing technologies on the market today have some major, inherent drawbacks that have origins in their design. In fact, most flat roofs fail to serve their main purpose just a few years after they are installed.

You are presented with so many choices for a flat roof and every roofing contractor will tell you their product is the best. But which one do you choose and how do you know that you are getting the best deal? Here we have summarized the most common and ‘popular’ flat roofing choices. You can be the judge and decide which is best for you.

Benefits of flat roof construction:

There is a common misconception among many home-improvement contractors and residential builders / architects that flat roofs = problems. The truth is that flat roofs are very convenient, easier to build, and cost less than pitched / sloped roofs. In some cases, a flat roof is the only way to go, for example, when you have a large size building. Building a reliable pitched roof in those cases will require extra engineering to accommodate for additional structural weight.

Flat roofs are also convenient for installing large HVAC equipment that otherwise would have to be installed on the ground. You can also use flat roof as a roof-top deck, patio or penthouse. Green roofs are also gaining popularity with environmentally conscious companies and organizations.

When you compare all the construction costs and environmental benefits, flat roofs by far surpass any sloped roof, for which the roof products of choice are oil-based asphalt shingles. These asphalt shingles end up in our land-fills every 12-15 years, and yet more and more of them are produced.

Limitations and Disadvantages of flat roofing:

Flat roofs also have a number of disadvantages. The main one is the fact that there is no slope and all the water/snow sits on the roof. While water can be taken care of with proper drainage, snow will sit on the roof until it melts. This requires the engineers / architects to implement building components with a higher structural load. Another disadvantage that haunted flat roof installations for over a century is ponding water. Until the invention of single ply membranes such as an IB roof, there was no effective and economical way to eliminate the leaks caused by ponding water. That had to be taken care of in the initial design/construction stage. Creating a slight pitch and multiple drains was required, and still ponding water caused over 75% of all flat roof leaks.

Now the ponding water problem is solved by either implementing a slight pitch to the roof – such as in ‘space metal buildings”, using tapered insulation to direct water flow toward drains and with the creation of IB PVC / CPA roofing with hot-air welded seams, ponding water is no longer a problem in small quantities. It is still necessary to have adequate drainage system, since a lot of ponding water can cause structural damages to your house or building.

Types of flat roof: Modern and Outdated roofing technologies.

Outdated (Multiple-Ply Roofs) – some are over 100 years old:

• Build-Up Roof (BUR)
• Tar & Gravel
• Bitumen (Modified Bitumen)
• Rolled Asphalt (usually a “single-ply” install, sometimes uses tar-paper as base ply)

Modern (Single-Ply Membranes)- created within last 30 years:

• IB Roof (PVC roofing) – IB PVC roofing membrane is one of the best low-slope and completely flat roofing products available, and that is precisely the reason why we only install IB roofs. With over 30 years of spotless reputation and leaks-free performance in many different climates – from Alaska’s frigid north-lands to Hawaii’s tropical paradise, IB roofs are protecting the buildings and everything inside, without a single material failure since 1978.
  
  IB roofs still feature the same chemical formula as its original design, and with hot-air welded seams, will maintain complete water-tightness over your roof.
• Epdm Rubber Roof – a widely used flat roofing material, mainly popular among contractors because of its low price and no special equipment needed to install the rubber roof. Still, rubber roofs are very prone to leaks, as the seams are glued together, and adhesive tends to break down within 5-7 years. Also in the residential roofing market (and not so much in commercial) there are too many contractors who will install rubber roofing products without proper knowledge and training. As a result, we often go to rubber roof repair service calls to fix problems caused by poor workmanship, often on fairly new roofs.
• TPO Roofing – a single ply thermoplastic roofing membrane similar to PVC roofs from a first glance. But as you start digging, you’ll find numerous problems with TPO roofs, mainly as a result of manufacturers skipping on adding important ingredients into formulation of the TPO membrane, and as a result, quietly scrapping as many as three major generations of the product.
• SFR – Sprayed Foam Roofing (not a single-ply)

Part I: Inferior and outdated flat roofing technologies

These are very common on older buildings, although many newer buildings also have these systems installed. They are rarely installed on any commercial building today. However, they continue to be produced, and many roofers still install them on residential and small commercial roofs. This is particularly due to their low cost of material, and roofers’ lack of experience with BETTER solutions. It is sad that there are some decent roofers offering such an inferior product to their customers. I often hear something along the lines of: “I’ve been doing ‘torch-down’ for 20 years, and it is the best” – very sad – so we will briefly describe them, without getting into details.

BUR / Tar & Gravel / Torch-down: Multiple-ply roof where each ‘tar-soaked’ ply is applied with a torch (yes, open flame on your roof!), or hot mopped (preheated tar transported to the roof and applied with a mop). Gravel goes on top of this ‘sandwich’ mainly as a protection layer from foot-traffic and sun’s devastating ultraviolet rays. There are many deviations from the above procedure, but they are all within a close range of similarity.

Modified Bitumen: It is also applied with a torch in a similar manner described above. It is however a different material than tar. Modified bitumen has rubber and elastomers added into the formula, so it is stronger and more flexible.

Rolled Asphalt: Similar to asphalt shingles – tar paper is saturated in asphalt, with crushed stones glued on top of it. Rolls are installed in an overlapping pattern, with cold-mop application and nails to attach it to the roof deck. Overlapping seams are sealed with tar.

Problems associated with flat roofs:

The nature of flat roofs’ problems is just that they are flat. Water does not run off the roof. Proper drainage must be in place to get rid of water accumulating on a roof. Usually older roofs are not leveled, so water puddles will appear here and there after every rain, and just sit there until it dries out. This is called standing or ponding water. Most roofing systems were not designed for ponding water. In fact, most manufacturers of the roofing systems on the market today, will void out the warranty if there is ponding water on the roof (we will get to this issue later). Other major problems for flat roofs, are penetrations such as skylights, vent or exhaust pipes, chimneys, roof hatches, drains, etc. However the biggest problem with flat roofs is the seams, because they are the most common areas where leaks occur.

Seams:

Seams exist on every flat roof (except tiny ’6×10 porch-type’ roofs, which can be covered with a single sheet of roofing membrane), and are usually put together with some sort of adhesive. After a few years the adhesive breaks due to severe weather changes (here in New England, temperature can change 25 degrees or more, in a matter of one day). Another major factor affecting seams’ adhesive is condensation, which always occurs underneath the roof covering. Condensation expands both in the winter and summer. The most dramatic expansion of condensation happens in the winter time when water freezes, expands and breaks the seam. The same happens to our roads. Think of all the potholes you drive over. Those too were caused by water freezing. In the summer water heats up and also expands. When you see bubbles on the roof surface, it is the water vapor lifting the membrane. The third major factor is actually quality of workmanship and the adhesive itself. For different roofing systems the process is different, but most of them share the same shortcoming – the need for using adhesives, be it glue, hot tar, liquid resin, etc. Adhesives are also required to flash any roof penetrations listed above, but here the workmanship is actually more of a factor than the adhesive.

Conclusion – let’s get real.

It is a shame that in the 21st century we are still using 19th century technology. Even more so, because nearly 50% of roofers in the on-line construction forums will advise you to choose a clearly inferior roof. These heavy and dirty roofs, heat up to 170 degrees and make your AC run like crazy in the summer. These very roofs start leaking prematurely and are impossible to fix. Why would some one acting in good faith actually recommend these? The answer is obvious – they don’t know any better. Fortunately there is ONE modern, technologically advanced flat roofing solution available on the market today – IB Roof. In fact, this solution has been around for a few decades now, and has a proved track record of 30 years of leak-free service!

Read more: Part II – Single-Ply Roofing Membranes – PVC, TPO & EPDM Rubber Roofing.

Flat Roofing systems: The purpose of a flat roof or any roof for that matter is to keep your home or building safe and dry. The roof MUST protect your investment from the elements such as rain, snow, and even the sun’s heat. However, many flat roofing technologies on the market today have some major, inherent drawbacks that have origins in their design. In fact, most flat roofs fail to serve their main purpose just a few years after they are installed.

You are presented with so many choices for a flat roof and every roofing contractor will tell you their product is the best. But which one do you choose and how do you know that you are getting the best deal? Here we have summarized the most common and ‘popular’ flat roofing choices. You can be the judge and decide which is best for you.

Benefits of flat roof construction:

There is a common misconception among many home-improvement contractors and residential builders / architects that flat roofs = problems. The truth is that flat roofs are very convenient, easier to build, and cost less than pitched / sloped roofs. In some cases, a flat roof is the only way to go, for example, when you have a large size building. Building a reliable pitched roof in those cases will require extra engineering to accommodate for additional structural weight.

Flat roofs are also convenient for installing large HVAC equipment that otherwise would have to be installed on the ground. You can also use flat roof as a roof-top deck, patio or penthouse. Green roofs are also gaining popularity with environmentally conscious companies and organizations.

When you compare all the construction costs and environmental benefits, flat roofs by far surpass any sloped roof, for which the roof products of choice are oil-based asphalt shingles. These asphalt shingles end up in our land-fills every 12-15 years, and yet more and more of them are produced.

Limitations and Disadvantages of flat roofing:

Flat roofs also have a number of disadvantages. The main one is the fact that there is no slope and all the water/snow sits on the roof. While water can be taken care of with proper drainage, snow will sit on the roof until it melts. This requires the engineers / architects to implement building components with a higher structural load. Another disadvantage that haunted flat roof installations for over a century is ponding water. Until the invention of single ply membranes such as an IB roof, there was no effective and economical way to eliminate the leaks caused by ponding water. That had to be taken care of in the initial design/construction stage. Creating a slight pitch and multiple drains was required, and still ponding water caused over 75% of all flat roof leaks.

Now the ponding water problem is solved by either implementing a slight pitch to the roof – such as in ‘space metal buildings”, using tapered insulation to direct water flow toward drains and with the creation of IB PVC / CPA roofing with hot-air welded seams, ponding water is no longer a problem in small quantities. It is still necessary to have adequate drainage system, since a lot of ponding water can cause structural damages to your house or building.

Types of flat roof: Modern and Outdated roofing technologies.

Outdated (Multiple-Ply Roofs) – some are over 100 years old:

• Build-Up Roof (BUR)
• Tar & Gravel
• Bitumen (Modified Bitumen)
• Rolled Asphalt (usually a “single-ply” install, sometimes uses tar-paper as base ply)

Modern (Single-Ply Membranes)- created within last 30 years:

• IB Roof (PVC roofing) – IB PVC roofing membrane is one of the best low-slope and completely flat roofing products available, and that is precisely the reason why we only install IB roofs. With over 30 years of spotless reputation and leaks-free performance in many different climates – from Alaska’s frigid north-lands to Hawaii’s tropical paradise, IB roofs are protecting the buildings and everything inside, without a single material failure since 1978.
  
  IB roofs still feature the same chemical formula as its original design, and with hot-air welded seams, will maintain complete water-tightness over your roof.
• Epdm Rubber Roof – a widely used flat roofing material, mainly popular among contractors because of its low price and no special equipment needed to install the rubber roof. Still, rubber roofs are very prone to leaks, as the seams are glued together, and adhesive tends to break down within 5-7 years. Also in the residential roofing market (and not so much in commercial) there are too many contractors who will install rubber roofing products without proper knowledge and training. As a result, we often go to rubber roof repair service calls to fix problems caused by poor workmanship, often on fairly new roofs.
• TPO Roofing – a single ply thermoplastic roofing membrane similar to PVC roofs from a first glance. But as you start digging, you’ll find numerous problems with TPO roofs, mainly as a result of manufacturers skipping on adding important ingredients into formulation of the TPO membrane, and as a result, quietly scrapping as many as three major generations of the product.
• SFR – Sprayed Foam Roofing (not a single-ply)

Part I: Inferior and outdated flat roofing technologies

These are very common on older buildings, although many newer buildings also have these systems installed. They are rarely installed on any commercial building today. However, they continue to be produced, and many roofers still install them on residential and small commercial roofs. This is particularly due to their low cost of material, and roofers’ lack of experience with BETTER solutions. It is sad that there are some decent roofers offering such an inferior product to their customers. I often hear something along the lines of: “I’ve been doing ‘torch-down’ for 20 years, and it is the best” – very sad – so we will briefly describe them, without getting into details.

BUR / Tar & Gravel / Torch-down: Multiple-ply roof where each ‘tar-soaked’ ply is applied with a torch (yes, open flame on your roof!), or hot mopped (preheated tar transported to the roof and applied with a mop). Gravel goes on top of this ‘sandwich’ mainly as a protection layer from foot-traffic and sun’s devastating ultraviolet rays. There are many deviations from the above procedure, but they are all within a close range of similarity.

Modified Bitumen: It is also applied with a torch in a similar manner described above. It is however a different material than tar. Modified bitumen has rubber and elastomers added into the formula, so it is stronger and more flexible.

Rolled Asphalt: Similar to asphalt shingles – tar paper is saturated in asphalt, with crushed stones glued on top of it. Rolls are installed in an overlapping pattern, with cold-mop application and nails to attach it to the roof deck. Overlapping seams are sealed with tar.

Problems associated with flat roofs:

The nature of flat roofs’ problems is just that they are flat. Water does not run off the roof. Proper drainage must be in place to get rid of water accumulating on a roof. Usually older roofs are not leveled, so water puddles will appear here and there after every rain, and just sit there until it dries out. This is called standing or ponding water. Most roofing systems were not designed for ponding water. In fact, most manufacturers of the roofing systems on the market today, will void out the warranty if there is ponding water on the roof (we will get to this issue later). Other major problems for flat roofs, are penetrations such as skylights, vent or exhaust pipes, chimneys, roof hatches, drains, etc. However the biggest problem with flat roofs is the seams, because they are the most common areas where leaks occur.

Seams:

Seams exist on every flat roof (except tiny ’6×10 porch-type’ roofs, which can be covered with a single sheet of roofing membrane), and are usually put together with some sort of adhesive. After a few years the adhesive breaks due to severe weather changes (here in New England, temperature can change 25 degrees or more, in a matter of one day). Another major factor affecting seams’ adhesive is condensation, which always occurs underneath the roof covering. Condensation expands both in the winter and summer. The most dramatic expansion of condensation happens in the winter time when water freezes, expands and breaks the seam. The same happens to our roads. Think of all the potholes you drive over. Those too were caused by water freezing. In the summer water heats up and also expands. When you see bubbles on the roof surface, it is the water vapor lifting the membrane. The third major factor is actually quality of workmanship and the adhesive itself. For different roofing systems the process is different, but most of them share the same shortcoming – the need for using adhesives, be it glue, hot tar, liquid resin, etc. Adhesives are also required to flash any roof penetrations listed above, but here the workmanship is actually more of a factor than the adhesive.

Conclusion – let’s get real.

It is a shame that in the 21st century we are still using 19th century technology. Even more so, because nearly 50% of roofers in the on-line construction forums will advise you to choose a clearly inferior roof. These heavy and dirty roofs, heat up to 170 degrees and make your AC run like crazy in the summer. These very roofs start leaking prematurely and are impossible to fix. Why would some one acting in good faith actually recommend these? The answer is obvious – they don’t know any better. Fortunately there is ONE modern, technologically advanced flat roofing solution available on the market today – IB Roof. In fact, this solution has been around for a few decades now, and has a proved track record of 30 years of leak-free service!

Read more: Part II – Single-Ply Roofing Membranes – PVC, TPO & EPDM Rubber Roofing.